Home > Checkpoint Code > Ibm Error Over Spec

Ibm Error Over Spec

Contents

VRM Reserved.   Parent topic: Light path diagnostics The request cannot be fulfilled by the server Light path diagnostics LEDs This section describes the LEDs on the light path diagnostics panel Check the system-event log for information about the error. When both the MEM and CNFG LEDs are lit, the memory configuration is invalid or the PCI Option ROM is out of resource. Make sure that the room temperature is not too high. this contact form

Show: 10 25 50 100 items per page Previous Next Feed for this topic Light path diagnostics LEDs This topic provides a description for each light path diagnostics LED and suggested If the CONFIG LED is not lit, a microprocessor failure occurs, complete the following steps: (Trained technician only) Make sure that the failing microprocessor and its heat sink, which are indicated The OVER SPEC LED on the light path diagnostics panel is lit, and the 12v channel A LED on the system board is lit. Also make sure that the microprocessors are supported by your server machine type or multi-node configuration. http://publib.boulder.ibm.com/infocenter/systemx/documentation/topic/com.ibm.sysx.7944.doc/r_light_path_diagnostics_table.html

Ibm X3650 Dasd Error Light

The LED that is lit determines which device you should troubleshoot. Check the system-event log in the Setup utility or IMM error messages. FAN A fan has failed, is operating too slowly, or has been removed.

  • If the CNFG LED and the MEM LED are lit, complete the following steps: Check the system-event log in the Setup utility or IMM error messages.
  • Reseat the failing fan, which is indicated by a lit LED near the fan connector on the system board.
  • If a voltage regulator has failed, replace the system board.
  • If the CNFG LED is lit, the system issues an invalid microprocessor configuration error.
  • The LOG LED might also be lit.
  • The system might detect a power supply error.
  • Replace any failing device. (Trained service technician only) Replace the system board.
  • See Server features and specifications for the server temperature information.

Make sure that both power supplies installed in the server are of the same rating or wattage. Turn off the server and disconnect the power from the server. If a memory expansion module is attached to the server, check to determine whether the front CNFG error LED is lit on the memory expansion module or the server. Ibm Light Path Diagnostics Checkpoint Codes Use the Setup utility to check the system-event log for information about the error.

When the CPU and CNFG LEDs are lit, an invalid microprocessor configuration has occurred. Ibm Light Path Diagnostics SP A service processor error has been detected. Note: A failing fan might not cause the fan LED to be lit. (Trained service technician only) Reseat the microprocessor board (see Removing the microprocessor-board assembly and Replacing the microprocessor-board assembly). http://www.ibm.com/support/knowledgecenter/ST5Q4U/com.ibm.storwize.v7000.unified.143.doc/bb1gt_r_lightpathdiapan.html Light path diagnostics panel LEDsFollow the suggested actions in the order in which they are listed in the Action column until the problem is solved.

CONFIG + MEM A hardware configuration error has occurred. Ibm Checkpoint Codes The TEMP LED might also be lit. Remove all installed PCI Express adapters. Replace the following components, in the order shown, restarting the server each time: PCI riser cards ServeRAID adapter Optional network adapter (Trained technician only) System board If the failure remains, go

Ibm Light Path Diagnostics

The OVER SPEC LED on the light path diagnostics panel is lit, and the 12v channel B LED on the system board is lit. http://publib.boulder.ibm.com/infocenter/systemx/documentation/topic/com.ibm.sysx.7944.doc/r_power_problems.html RAID Reserved   SP The service processor (the IMM) has failed. Ibm X3650 Dasd Error Light Do certain motherboard required certain power levels ? Ibm Checkpoint Code 9f Remove all installed PCI Express adapters, hard disk drives or solid state drives, and drive backplanes.

Check the LEDs on the system board to identify the component that caused the error. Check the power-supply that has an lit amber LED (see Power-supply LEDs). Note: The server will not power-on when the microprocessor in socket 1 or 2 is not installed in the server. (Trained service technician only) Toggle the switch block (SW4), bit 3 Complete the following steps to correct the problem: Check the power-supply with a lit yellow LED (see Power-supply LEDs). Ibm X3650 M3 Checkpoint Code Display 9f

See Replacing a microprocessor and heat sink for information about installing a microprocessor. Make sure that the room temperature is not too high. Complete the following steps to correct the problem: Check the microprocessors that were just installed to make sure that they are compatible with each other and use the Setup utility and http://bookmarq.net/checkpoint-code/ibm-x3550-over-spec-error.php Remove the PCI riser card from PCI riser connector 2 and the microprocessor in socket 2.

Note: The server will not power-on when the microprocessor in socket 1 or 2 is not installed in the server. (Trained service technician only) Toggle the switch block (SW4), bit 3 Ibm Light Path Diagnostics Dasd 9f The system returned: (22) Invalid argument The remote host or network may be down. If the failure remains, go to the "Before you call IBM Service" website for additional troubleshooting information.

Make sure that the reset button is working correctly: Disconnect the server power cords.

A failing fan can cause the TEMP LED to be lit. Remove the SAS/SATA RAID riser card, DIMMs in connectors 1 through 9, and the microprocessor in socket 1. Thanks More... Brd Error On Ibm Server A failing fan can cause the TEMP LED to be lit.

The LED that is lit determines which device you should troubleshoot. See System-board switches and jumpers for the location of the SW4 switch block on the system board. For more information, go to http://www.ibm.com/support/entry/portal/docdisplay? http://bookmarq.net/checkpoint-code/ibm-xseries-345-over-spec-error-lights.php The following table describes the LEDs on the light path diagnostics panel and suggested actions to correct the detected problems.

Find the suspected board by checking the LEDs on the I/O-board shuttle and microprocessor board. Replace the power supply. Restart the server to see whether the problem remains. Replace the following components, in the order shown, restarting the server each time: PCI riser card (Trained service technician only) Replace the system board.

A hard disk drive has failed or is missing. If the Pwr Rail (1, 2, 3, 4, 5, or 6) error was also detected, follow actions listed in Power problems and Solving power problems. Please try the request again. Check the system-error log for information about the error.

Replace the failing fan, which is indicated by a lit LED near the fan connector on the system board (see Removing a hot-swap fan for more information). If the CNFG LED and the CPU LED are lit, complete the following steps to correct the problem: Check the microprocessors that were just installed to make sure that they are Check the system-event log to determine the reason for the lit LED (see Event logs). One PCI riser-card assembly must always be present in PCI connector 2.

Restart the server to see whether the problem remains. (Trained service technician only) Reinstall the microprocessor in socket 1 and restart the server. Make sure that the power supplies are seated correctly. I read somewhere that certian models of x 345 require 300w power, while others require 350w. Regards, Alexander Novikov Russia, Moscow More...

If a memory expansion module is attached to the server, check to determine whether the front FAN error LED is lit on the memory expansion module or the server. If an action step is preceded by "(Trained service technician only)", that step must be performed only by a trained service technician. LINK Reserved.   LOG An error message has been written to the system-event log Check the IMM system event log and the system-error log for information about the error.




© Copyright 2017 bookmarq.net. All rights reserved.