Home > Checkpoint Code > Ibm X346 Error Light

Ibm X346 Error Light

Contents

Replace any failing device. (Trained service technician only) Replace the system board. For more information, go to the "Before you call IBM Service" website. If the 12 V channel C error LED is lit, complete the following steps: Turn off the server and disconnect the power from the server. Reinstall each device that you removed in step 2 one at a time, starting the server each time, to isolate the failing device. Check This Out

Hi Alexander, No I didn't remove VRM. I'm not sure what I'm supposed to do to clear the panel now...the documentation says to use the reset button on the panel (the tiny one). Complete the following steps to correct the problem: Check the microprocessors that were just installed to make sure that they are compatible with each other and use the Setup utility and but its better to get rid of it, so that if any other failure occurs you will be sure that its new one. http://www.ibm.com/support/knowledgecenter/ST5Q4U/com.ibm.storwize.v7000.unified.143.doc/bb1gt_r_lightpathdiapan.html

Ibm Light Path Diagnostics

If you hit the remind button again, it should show you the last LED that was illuminated on the Light Path panel.Well, to the extent that I replaced the failed PS I keed I keed! DarkSyd Ars Praefectus Registered: Nov 24, 1999Posts: 5769 Posted: Fri Apr 02, 2010 2:11 pm Hairy Gunt wrote:A blinking orange system-error LED simply means the remind button has been pressed.It normally See Features and specifications for the server temperature information.

share|improve this answer answered Jan 20 '14 at 16:38 TheCleaner 25.7k1285156 I have seen that in the manual. The client says that everything is functioning on the server right now, and the light has been on for a while. If the power supply has failed, call for service. Ibm X3650 M3 Checkpoint Code Display 9f Thanks Mohamed Sherif Log in to reply.

Hi Alexander, sorry but I'm new in IBM world. Login. i'm not sure but I think it upgraded the system BIOS. Restart.

To access the light path diagnostics panel, slide the latch to the left on the front of the light path diagnostics drawer. Ibm Checkpoint Codes Make sure that both power supplies installed in the server are of the same type. Regards, Alexander Novikov Russia, Moscow Log in to reply. The HP folks have certainly been trying to talk me into their gear, but, blinky lights aside, I'm happy with our IBM gear for now.

Light Path Diagnostics Checkpoint Codes

mohamedsherif 2700036J8Q ‏2010-05-17T10:41:36Z Hi Alexander, No I didn't remove VRM. You can think of the first part as the test code and the second part as the fault code. Ibm Light Path Diagnostics Can anyone assist me in getting this resolved? Ibm Checkpoint Code 9f After restarting the server it stopped working and i get error code 199 processor mismatch system halted.

Novikov_Alexander 100000HTD5 6932 Posts Re: IBM X346 not working ‏2010-05-16T17:04:44Z This is the accepted answer. More... Parent topic: Light path diagnostics panel Parent topic: Light path diagnostics Share?Profiles ▼Communities ▼Apps ▼ Forums System x Server Log in to participate Expanded section▼Topic Tags ? If you hit the remind button again, it should show you the last LED that was illuminated on the Light Path panel. Ibm Light Path Diagnostics Checkpoint Codes

  • in addition i can't find the server model in the URL u sent.
  • If the power supply has failed, call for service.
  • If an action step is preceded by "(Trained service technician only)", that step must be performed only by a trained service technician.

TEMP The system temperature has exceeded a threshold level. I keed I keed! mohamedsherif 2700036J8Q 11 Posts Re: IBM X346 not working ‏2010-05-16T13:38:04Z This is the accepted answer. this contact form DarkSyd Ars Praefectus Registered: Nov 24, 1999Posts: 5769 Posted: Wed Mar 31, 2010 8:44 pm I will check that when I get in tomorrow...thanks!

Novikov_Alexander 100000HTD5 6932 Posts Re: IBM X346 not working ‏2010-05-17T14:18:27Z This is the accepted answer. Ibm X3650 Dasd Error Light Light path diagnostics panel LEDsFollow the suggested actions in the order in which they are listed in the Action column until the problem is solved. I had ServeRAID issues and already replaced the RAID card. –Bob ONeill Jan 22 '14 at 13:38 The x346 is old anyway...you're doing yourself a favor to trash it.

An error has occurred and cannot be isolated.

mohamedsherif 2700036J8Q 11 Posts Re: IBM X346 not working ‏2010-05-17T16:18:44Z This is the accepted answer. What did you do before faced with error? System account and sharepoint farm account? Ibm Light Path Diagnostics Dasd 9f However, when you open the light path panel, nothing is lit up, so I can't tell what component is having the problem.

Hide thumbs Also See for xSeries 346 Hardware maintenance manual and troubleshooting manual - 172 pagesUser manual - 62 pagesInstallation manual - 108 pages 1 2 3 4 5 Novikov_Alexander 100000HTD5 6932 Posts Re: IBM X346 not working ‏2010-05-17T08:51:19Z This is the accepted answer. Another alternative is to get with your VAR that sold you the server, as they might have IBM certified techs that can assist you. http://bookmarq.net/checkpoint-code/ibm-x3650-dasd-error-light.php Check the LEDs on the system board to identify the component that caused the error.

Reinstall each device that was removed in step 2 one at a time, starting the server each time, to isolate the failing device. Lo and behold, your blog is useful to me once again! Topic Forum Directory >‎ dW >‎ Eserver >‎ Forum: System x Server >‎ Topic: IBM X346 not working 20 replies Latest Post - ‏2014-02-07T03:34:09Z by Novikov_Alexander Display:ConversationsBy Date 1-21 of 21 If the problem remains, go to the "Before you call IBM Service" website.

One easy check is to remove all the memory and try to boot and see if it beeps differently. Replace the failed power supply. Note: The server will not power-on when the microprocessor in socket 1 or 2 is not installed in the server. (Trained service technician only) Toggle the switch block (SW4), bit 3 If the CNFG LED is not lit, the system might detect a memory error.

Good luck, Alexander Novikov Russia, Moscow More... How should a coloured dropdown be styled using Google Material? Conditions in modeler field calculator Meaning of "Sue me" Project Euler Problem 35: counting circular primes below 1 million can the same river be deep and fordable Determine the DC of Find us on Google+ System Specific Diagnostic and POST Error Messages: IBM Diagnostic Error Codes Compaq Desktop Systems Diagnostic and POST Errors BIOS Related Pages: BIOS Data Area BiosCentral Forums BIOS

Replace any components that are identified in the error logs.




© Copyright 2017 bookmarq.net. All rights reserved.