Home > Checkpoint Code > Ibm X3550 Error Code 9f

Ibm X3550 Error Code 9f

Contents

If the 12 V channel A error LED is lit, complete the following steps: Turn off the server and disconnect the power from the server. Replace the following components one at a time, in the order shown, restarting the server each time: Each adapter (Trained service technician only) System board 3xx0007 (xx can be 00 - Power-supply LEDs Use this information to view power-supply LEDs. Reseat the DIMMs and restart the server. this contact form

Replace the hard disk drive backplane. Problem determination tips Because of the variety of hardware and software combinations that can encounter, use the following information to assist you in problem determination. A new error occurs, causing the system-error LED to be lit again. Note: Each time you install or remove a DIMM, you must disconnect the server from the power source; then, wait 10 seconds before restarting the server.

Ibm X3650 M3 Checkpoint Code Display 9f

Memory online-spare channel has been activated to back up a failed DIMM. If the problem is related to a DIMM, replace the failing DIMM. (Trained service technician only) If the problem occurs on the same DIMM connector, check the DIMM connector. Reconnect the server to the power source, then turn on the server. 305000A RTC date/time is incorrect Adjust the date and time settings in the Setup utility, and then restart the

  1. The light path diagnostics panel must remain in the server when the server is running to ensure proper cooling.
  2. If the error still occurs on the same DIMM, replace the affected DIMM. (Trained service technician only) If the problem occurs on the same DIMM connector, check the DIMM connector.
  3. When both the PS and CNFG LEDs are lit, the power supply configuration is invalid.
  4. Turn off the server and remove it from the power source.

Undo any recent configuration changes, or clear CMOS memory to restore the settings to the default values (see System-board switches and jumpers). error, note the lit LED on or beside the component. Replace any failing device. (Trained service technician only) Replace the system board. Ibm Light Path Diagnostics Checkpoint Codes Check the LEDs on the system board to identify the component that is causing the error.

Check the system-event log in the Setup utility or IMM error messages. Ibm Checkpoint Code 9f Troubleshooting tables Use the troubleshooting tables to find solutions to problems that have identifiable symptoms. Update the IMM firmware to the latest level (see Updating the firmware). http://publib.boulder.ibm.com/infocenter/systemx/documentation/topic/com.ibm.sysx.7945.doc/r_light_path_diagnostics_leds.html IBM,x3550 M3,IBM 3550 M3,IBM System x3550 M3,System x3550 M3,IBM xSeries 3550 M3,IBM x3550 M3 server,IBM x3550 M3 server,IBM server x3550 ...

RAID Reserved. Ibm Checkpoint Codes Check the system-event log in the Setup utility or IMM error messages. Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. A hard disk drive has failed or is missing.

Ibm Checkpoint Code 9f

Make sure that the room temperature is not too high. http://publib.boulder.ibm.com/infocenter/systemx/documentation/topic/com.ibm.sysx.7944.doc/r_post_error_codes.html Run the Setup utility, select Startup Options, and change the boot priority to change the load order of the optional-device ROM code. Ibm X3650 M3 Checkpoint Code Display 9f Run the Setup utility and select System Information > System Summary > Processor Details to view the microprocessor information to compare the installed microprocessor specifications. (Trained service technician only) Remove and Ibm Light Path Diagnostics If you cannot isolate the failing adapter through the LEDs and the information in the system-event log, remove one adapter at a time from the failing PCI bus, and restart the

Slide the latch to the left on the front of the light path diagnostics drawer to access the light path diagnostics panel. weblink Check the event log for uncorrected DIMM failure events. 00580A1 Invalid DIMM population for mirroring mode Note: Each time you install or remove a DIMM, you must disconnect the server from Use the Setup utility to check the system-event log for information about the error. Check the error log to identify where the over-temperature condition was measured. Light Path Diagnostics Checkpoint Codes

Reseat the hard disk drive backplane. The TEMP LED might also be lit. If a voltage regulator has failed, replace the system board. http://bookmarq.net/checkpoint-code/ibm-x3550-over-spec-error.php If the CNFG LED is lit, the system issues an invalid microprocessor configuration error.

Run the Setup utility and select System Information > System Summary > Processor Details to view the microprocessor information to compare the installed microprocessor specifications. (Trained service technician only) Remove and Ibm Light Path Diagnostics Dasd 9f To acknowledge a system error but not take immediate action, press the remind button and place light path diagnostics in remind mode. Lit LEDs on this panel indicate the type of error that has occurred.

CPU When only the CPU LED is lit, a microprocessor has failed.

Check the LEDs on the system board to identify the component that caused the error. If the CNFG LED and the PS LED are lit, the system issues an invalid power configuration error. Restart the server to see whether the problem remains. Ibm X3650 Dasd Error Light Diagnostic tools The section introduces available tools to help you diagnose and solve hardware-related problems.

The error is not represented by a light path diagnostics LED. Make sure that both power supplies installed in the server are of the same type. Update the server firmware to the latest level (see Updating the firmware). http://bookmarq.net/checkpoint-code/ibm-error-code-9f.php This feature helps you to isolate the problem when the operating system is shut down.

If possible, rearrange the order of the adapters in the PCI slots to change the load order of the optional-device ROM code. Check the system-error logs for information about the error. Note: The server will not power-on when the microprocessor in socket 1 or 2 is not installed in the server. (Trained service technician only) Toggle the switch block (SW4), bit 3 See System-board switches and jumpers for the location of the SW4 switch block on the system board.

Note: When you slide the light path diagnostics panel out of the server to check the LEDs or checkpoint codes, do not run the server continuously with light path diagnostics panel If any of the power channel error LEDs (A, B, C, D, E, or AUX) on the system board are lit also, see the section about power-channel error LEDs in Power If a damage is found, replace the system board. (Trained Service technician only) Replace the affected microprocessor. 0051004 DIMM presence detected read/write failure Note: Each time you install or remove a PS1 PS2 VRM CNFG NMI S ERR DASD RAID TEMP BRD Chapter 5.

Follow steps indicated in POST error codes and Integrated management module error messages. If the system-error LED is lit, it indicates that an error has occurred; go to step 2. See Features and specifications for the server temperature information. Check the LEDs on the PCI slots to identify the component that is causing the error.

If the CNFG LED and the MEM LED are lit, complete the following step: Check the system-event log in the Setup utility or IMM error messages. If you cannot diagnose and correct a problem by using the information in this chapter, see Getting help and technical assistance for more information. Hide thumbs Also See for x3550 - System - 7978 Problem determination and service manual - 190 pages 1 2 3 4 5 6 7 8 9 10 11 Reseat the hard disk drive backplane.




© Copyright 2017 bookmarq.net. All rights reserved.